03/26/2012 15:11:35.400 - Debug - VPN IKE - RECEIVED ISAKMP OAK QM (InitCookie:0x8cb7f01ad26b896f RespCookie:0x7d6fa1fb7a5384b1, MsgID: 0xE15EE87A) *(HASH, SA, NON

Mar 31, 2014 · For a PIX/ASA Security Appliance 7.x LAN-to-LAN (L2L) IPsec VPN configuration, you must specify the of the tunnel group as theRemote peer IP Address(remote tunnel end) in the tunnel-group type ipsec-l2l command for the creation and management of the database of connection-specific records for IPsec. Aug 05, 2019 · A site-to-site IPSec VPN between a Palo Alto Networks firewall and a firewall from a different vendor is configured. Phase 1 succeeds, but Phase 2 negotiation fails. A look at the ikemgr.log with the CLI command: Check if the network address is correct and matches what is expected by the remote VPN endpoint. Check also the ID type defined in "Phase 1 advanced" is consistent with the type defined in the router. Warning: the local ID on the router is the remote ID on the VPN Client and conversely ! Note:it is not mandatory the ID value is an IP address. The ID information should contain the public IP address, from which the VPN peer gateway expects the proposal to arrive. In SmartDashboard, open the Security Gateway / Cluster object. Expand the "IPSec VPN" (older versions say only "VPN"). Click on "Link Selection". Select the "Always use this IP address". Troubleshooting Guide: IKE IPSec VPN Initialization 02/2007 Introduction This guide will present the basic information required to troubleshoot problems in establishing an IKE IPSec VPN Tunnel. The guide will first present the basic premise of IKE negotiation, protocol support, and noteworthy configuration details. After setting up the VPN, during Phase II we get a "Received notify: INVALID_ID_INFO" From what I remember and have read, this is usually due to the networks tabs not lining up properly. For local network, I am choosing the X0 interface as my network, which is a 192.168.x.x /24 on both sides.

好的，所以我有一个简单的VPN IPSEC设置，使用一个具有公共IP地址和172.16.255.1的回送接口的Linux主机。 在右侧，我有一个Cisco ASA 5505 9.1。 问题是Cisco ASA在debugging“PHASE 2 Completed”时说，所以我知道与我的ISKMP协商没有冲突。

Jan 08, 2010 · Sonicwall Model: Tz 215 Firmware Version: SonicOS Enhanced 5.8.1.12-46o The following IPSec settings will be used in this section of this configuration document: Sonicwall Tz 215: Phase I Main mode 3DES SHA-1 MODP Group 2 (1024 bits) for DH SA lifetime of 28,800 seconds Preshared Secret Phase II 3DES SHA-1 MODP Group 2 (1024 bits) for DH SA 07:03:27 Jan 22 483 VPN Warning Received notify: INVALID_ID_INFO [ASAip.218], 500 [SWip].67, 500. 07:03:27 Jan 22 346 VPN Inform IKE Initiator: Start Quick Mode (Phase 2). [ASAip.218], 500 [SWip].67, 500 VPN Policy: St.JTecnicar

好的，所以我有一个简单的VPN IPSEC设置，使用一个具有公共IP地址和172.16.255.1的回送接口的Linux主机。 在右侧，我有一个Cisco ASA 5505 9.1。 问题是Cisco ASA在debugging“PHASE 2 Completed”时说，所以我知道与我的ISKMP协商没有冲突。

Ok, so I have a simple VPN IPSEC setup with a single Linux host that has a public IP address and a loopback interface of 172.16.255.1. On the right side I have a Cisco ASA 5505 9.1. the issue is the Jan 08, 2010 · Sonicwall Model: Tz 215 Firmware Version: SonicOS Enhanced 5.8.1.12-46o The following IPSec settings will be used in this section of this configuration document: Sonicwall Tz 215: Phase I Main mode 3DES SHA-1 MODP Group 2 (1024 bits) for DH SA lifetime of 28,800 seconds Preshared Secret Phase II 3DES SHA-1 MODP Group 2 (1024 bits) for DH SA 07:03:27 Jan 22 483 VPN Warning Received notify: INVALID_ID_INFO [ASAip.218], 500 [SWip].67, 500. 07:03:27 Jan 22 346 VPN Inform IKE Initiator: Start Quick Mode (Phase 2). [ASAip.218], 500 [SWip].67, 500 VPN Policy: St.JTecnicar Dec 09, 2013 · 1754 11/29/2001 16:20:18.500 Group = y.y.172.63, IP = y.y.172.63, Received non-routing Notify message: Invalid ID info (18) The following indicates that the local gateway is not finding matching interesting traffic. 事例2 IPsecを使ったVPNで通信が失敗する Notify message type No SA for received ESP(0xbd7ffcac) packet from 198.51.100.200 Oct 19, 2013 · Site-to-site VPN connections are very easy to create between Sonicwall devices, almost ridiculously easy. Here’s how to do it. Sonicwall let’s you set up site-to-site VPN’s in a number of ways. I find the easiest and fastest way is to use the procedure that Sonicwall recommends when one of the VPN gateway Sonicwalls receives its …